Almost all Porsches from about 1984 use a sophisticated Bosch engine management system called Motronic. The Motronic system (also called the Digital Motor Electronics, or DME) is hands down the best overall fuel injection system that you can use when you consider price and performance. Ignition timing and fuel delivery are all controlled by a digital map that is recorded in a removable chip within the main fuel injection (DME) computer. The computer takes input from a variety of sensors that are located on the engine梕ngine coolant temperature, crank angle, throttle position, exhaust gas oxygen (mixture), ambient air temperature, and mass airflow. The DME flash memory chip is programmed from the factory with certain performance characteristics (mostly conservative) so that the engine will react well under a host of varying conditions.
As with any electronic device, components can fail, triggering problems with the system. The Porsche Motronic system is designed to react to these failures and indicate them to the driver, so that they can be fixed. If one of the computer抯 sensors is not working properly, then the computer may not be able to successfully identify the current state of the engine and choose the appropriate fuel mixture or timing advance level. When this happens, the fuel mileage drops, engine performance suffers, emissions increase, and the car typically illuminates the check engine light.
Pre-1995 Porsches were equipped with what is known as OBD I (On-Board Diagnostics Level I). Starting in 1996, they were equipped with a more advanced version called OBD II, which was mandated by the U.S. government in order to standardize automotive repair and diagnostics. The OBD system is responsible for monitoring and checking all of the fuel injection sensors and systems in the vehicle, and turns on the check engine lamp if it finds a problem or irregularity with one of them. If there is a problem with a sensor or component, the computer lodges a Diagnostic Trouble Code (DTC) in the main computer until it is read and reset.
In order to accurately find the sensor and fix the problem, you will need to find out which error code is being triggered by the computer. There is no method to pull these codes out of your Porsche without the use of a computer tool. The factory has produced a version of this tool for use by Porsche dealers called the Porsche System Tester 2 (PST2). Unfortunately, finding one of these is next to impossible, and they cost about $4,000 used anyway. There抯 a newer version of the PST2 called the PIWIS, but getting your hands on one of those costs about $20,000 and a $1,000 maintenance contract from Porsche. You can indeed use a standard off-the-shelf OBD II reader available at any auto parts store, but it will only give you the standard read-out codes for the fuel injection system梱ou will not be able to do any extra diagnostics on any other area of the car.
Thankfully though, there is aftermarket software available produced by Durametric that performs almost all of important reading functions that the PST2 does. It runs on a windows laptop computer, and the cost is about $300 for the home-based version that will allow you to read codes on up to three cars. If you抮e planning on working on your 911 Carrera at all, I suggest that you pick up this essential tool.
With a standard ODB II code reader, you can access and reset the codes on the car that are related only to the fuel injection system. The PST2 and Durametric software allow you to dig deep into the various systems of the car and read values from the various systems of the car (air bag, ABS, Tiptronic transmission, alarm, seat memory, heating & A/C). The Durametric tool does not program the computer though梱ou are still at the mercy of the dealer when it comes to making changes to any of the non杅uel injection settings on your car.
When you obtain the trouble codes output by the PST2, you can look them up in the Porsche ODB II factory diagnostic book (expensive) or refer to the Bentley Workshop Manual for additional details. Both manuals have extensive sections describing the various faults and what is needed to fix them.
Tip: Wire harnesses are a major cause of fault code problems. As the cars get older, the wiring harnesses have a habit of becoming what is commonly known as 搘ork-hardened.? This causes the wiring to become brittle and often break inside of its plastic sheath. Only by testing the continuity of the wires end-for-end will you be able to determine whether the wire is broken or not.
From:obd2 news
留言列表
